Resources Required
Two '/*" x Γ 18-gauge sterling silver sheet silver Two 7/«" sterling silver bar components Two five.three mm x 3.two mm sixteen-gauge sterling silver oval soar rings Two sterling silver ear wires
Applications Wanted
Ruler
Marker
Jeweler's observed or tin snips Masking tape
Concrete block or landscape paver
Hammer
File
High-quality grit sanding pad Awl
Really hard, flat area /Îί’ drill little bit
Handheld rotary Device, flex shaft, or drill press Liver of sulfur or oxidizing Alternative Great metal wool Polishing fabric
Two pairs of chain nose pliers
1.Make use of the ruler to measure and mark two
rectangle parts of 18-gauge sterling sheet silver.
two.Utilizing a jeweler's saw or tin snips, Slash the 18-gauge sterling sheet silver into two Vi" x Γ rectangles (if you're going to be creating the bracelet and pendant tasks, you might want to Minimize all the rectangle silver items required for one other assignments and texture all of them at a single time).
three.Place the two W x Γ sterling silver rectangle parts onto the sticky aspect of a bit of masking tape. This will allow you to to carry the silver rectangles in place when you are texturing them, and may also support to keep your fingertips at a safe length to prevent hitting them with the hammer.
4.Spot the bit of masking tape with the silver rectangles sticky side down onto a concrete block or landscape paver.
5.By using a hammer, Carefully strike the tape-covered silver rectangles using a agency strike, but Really don't strike much too tricky. You can attain the desired texture much more very easily with several delicate strikes as opposed to several difficult strikes. Lift the tape frequently and Look at the development with the texturing, ensuring that the whole area with the silver rectangles is getting a uniform texture. The area will glance much like sandpaper if you are employing a concrete block. If you attain the specified texture, take away the silver rectangles in the masking tape.
six.the silver rectangles may have a slight curve to them, and the perimeters will probably be misshapen and sharp Once you texture them. You are able to depart the silver rectangles curved or, to flatten them, place the silver rectangles on a hard, flat area and use a rawhide mallet to flatten them. If you do not Use a men's fashion rings rawhide mallet, you are able to position the silver rectangles on a tough, flat surface, go over the items with a thick piece of scrap leather, and make use of a hammer to gently tap the leather lined silver rectangles to flatten them.
seven.You must utilize a file men's fashion rings to get rid of any rough or sharp edges. Use a wonderful grit sanding pad to go about the world in which you have filed to easy the perimeters and remove any file marks.
8.Measure from a single conclude of every textured silver rectangle and spot a mark in men's rings personalized and engraved the center of each piece. This is where the holes might be drilled to connect the leap ring and bar elements.
9.Placed on the protection glasses. Location the textured silver rectangles on to a tough, flat surface area. Location The purpose of your awl over the mark you designed '/t" from your finish of the rectangle items and use a hammer to firmly strike once on the highest in the awl to create a pilot gap for drilling the holes to the silver rectangles.
10.Employing a drill bit, drill holes into each on the silver rectangles having a handheld rotary Software, flex shaft, or drill press. Make sure to wear basic safety Eyeglasses.
11.Make use of the file or sanding pad to eliminate any burs or rough edges remaining from drilling holes in to the silver rectangles.
twelve.Utilize liver of sulfur or oxidizing Remedy to your textured silver rectangles, bar components. and leap rings. It is vital to follow any security suggestions the maker implies when dealing with any chemicals.
13.Right after implementing the oxidizing solution, use good steel wool to get rid of the darkened regions to the lifted area of your silver rectangles, leaving a few of the textured locations dark. Rub the good steel wool gents ring more than the jump rings and bar components to eliminate some although not each of the darkened regions. Rinse with drinking water, dry, and rub with polishing cloth.
fourteen.With two pair of chain nose pliers pointing up, hold the bounce ring with the opening at the best. Roll just one of your respective wrists from you and your other wrist towards you, opening the leap ring only around necessary. To shut the leap ring, keep it the exact same way and roll your wrists in the other way (imagine holding a bit of paper and tearing it). Never ever pull the jump ring finishes out as this may weaken the steel, and it will be challenging to close the leap ring.
fifteen.Include the bar part and textured silver rectangle towards the soar ring. Shut the leap ring.
sixteen.Carefully open the loop at the bottom with the ear wire, include the opposite stop with the bar component. then shut the ear wire gents ring loop.
seventeen.Repeat these actions for the next earring.